FlexRadio
Categories
- Genius Products The Genius products forum contains articles related to using The 4O3A Genius products with FlexRadio products
- HelpDesk Information This forum contains articles related to the use of the HelpDesk
- FLEX Signature Series Amateur Radio Products This forum is for the Maestro, FLEX-6000 and FLEX-8000 series SDRs.
- FLEX Series Amateur Radio Products - Discontiued This forum is for the FLEX-1500, FLEX-3000 and FLEX-5000 series radios
Promoted articles
- Resetting the TGXL (Tuner Genius XL)
- Configuring ICOM exciters with the PGXL, TGXL and Antenna Genius
- Configuring the "Dream Station" - FLEX-8000/6000 with the PGXL/TGXL/AG for Proper Operation
- Required Browsers needed for Accessing the HelpDesk
- How to Access your Support Tickets via the HelpDesk portal
- How to Submit a Request for Technical Support
- SmartSDR Serial Passthrough Feature
- How to Connect 3rd Party Microphones with Two-Connector MONO (TS) or Three-Connector "Balanced" TRS Plugs to the Maestro C
- How to Upgrade the Software/Firmware on an M-Model Radio
- How to Mitigate Common Mode Interference
- Exporting and Importing your SmartSDR Profiles
- How to Factory Reset your FLEX-6000/FLEX-8000 Radio
- Adjusting your Microphone Settings for Best TX Audio
- What is an EMP and Why Should I Care About It?
- Getting Started with the FLEX-6000
- Configuring the USB Cables Feature for the FLEX-6000/FLEX-8000
- What is Port Forwarding and How do you do it?
- WiFi Requirements and Performance with Maestro
- How to determine the amount of RF Preamp gain to apply for band conditions
- Grounding Systems in the Ham Shack - Paradigms, Facts and Fallacies
- Rules for EQing Voice for Optimal Phone Operation
- How To Set The Windows Default Playback & Recording Audio Device
- How to Build a Quiet Station for Better Reception
- How to Change Default Audio Sound Device
- Why Does My Radio Say I Am "Out Of Band" When My Frequency Readout Says I Am Not?
- Why does the Maestro "C" Require a 24 VDC Supply Voltage?
- Managing Your SmartLink Account and Password
- Why Doesn't the S-Meter Read S0 when the Antenna is Disconnected?
- How does the Automatic Gain Control (AGC) work in SmartSDR
- How to Completely Reset a FLEX-8000/6000
- How to Setup SmartLink Video
- ADC Overload with Direct Sampling SDRs - Myths Debunked
- Are there any video cards that do not work well with SmartSDR for Windows?
- Windows HRESULT Error Codes and Resolutions
- How to Fix the AMBER Light Staying Lit on the FLEX-6000 Series Power Button.
- How to fix a blank SmartLink login screen when running Win10 or Win8
- Resolving the "single red blink" Fan Error on Start Up
- How to fix SmartSDR CAT "Trial period has Expired. Program is disabled now" Errors
- How to Determine if Your Network is Configured for Multiple NATing
- How to Manually Uninstall the FlexVSP Driver
- How to Manually Reinstall the SmartSDR FlexControl Driver
- Troubleshooting FlexVSP Not Running Errors
- How to Repair the FlexVSP Virtual Serial Port Driver
- How to do a Complete uninstall of SmartSDR for Windows from your PC
- How to Manually Reinstall the FlexVSP Drivers
- Reasons for Wireless Network Performance Problems
- How to Change the Com Port Assignment for a FlexControl
- What are DPCs and Why Do They Matter?
- Troubleshooting Graphics Issues with SmartSDR-Win
- How to Mitigate FlexControl Latency
- Manually Reinstalling the FLEX-1500 Streaming USB driver
- FLEX-5000 Accessories and Upgrades
- New Power Down Sequence for FLEX-5000C
- Accessing the FlexRadio Knowledge Center
- How to Configure the Operating Parameters in the FLEX Firewire Control Panel
- Troubleshooting Firewire Connectivity Issues
- How to Manually Reinstall a PowerSDR FlexControl
- How to Change the Display DPI settings for PowerSDR